USB High Speed Power Delivery Series are now available here. With added Power Delivery(PD) functionality to the existing High Speed Series.

The FT2232H is FTDI’s 5th generation of USB devices. The FT2232H is a USB 2.0 Hi-Speed (480Mb/s) to UART/FIFO IC. It has the capability of being configured in a variety of industry standard serial or parallel interfaces.

The FT2232H is available in Pb-free (RoHS compliant) 64-pin LQFP/QFN and 56-pin QVFN packages.

Building on the innovative features of the FT2232, the FT2232H has two multi-protocol synchronous serial engines (MPSSEs) which allow for communication using JTAG, I2C and SPI on two channels simultaneously.

Key Hardware Features

• Single chip USB to dual serial / parallel ports with a variety of configurations.
• Entire USB protocol handled on the chip. No USB specific firmware programming required.
• USB 2.0 High Speed (480Mbits/second) and Full Speed (12Mbits/second) compatible.
• Dual Multi-Protocol Synchronous Serial Engine (MPSSE) to simplify synchronous serial protocol (USB to JTAG, I2C, SPI or bit-bang) design.
• Dual independent UART or FIFO ports configurable using MPSSEs.
• Independent Baud rate generators.
• RS232/RS422/RS485 UART Transfer Data Rate up to 12Mbaud. (RS232 Data Rate limited by external level shifter).
• USB to parallel FIFO transfer data rate up to 10Mbyte/sec.
• Single channel synchronous FIFO mode for transfers up to 40 Mbytes/sec.
• CPU-style FIFO interface mode simplifies CPU interface design.
• MCU host bus emulation mode configuration option.
• Fast Opto-Isolated serial interface option.
• FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.
• Adjustable receive buffer timeout.
• Option for transmit and receive LED drive signals on each channel.
• Enhanced bit-bang Mode interface option with RD# and WR# strobes.
• FT245B-style FIFO interface option with bidirectional data bus and simple 4 wire handshake interface.
• Highly integrated design includes +1.8V LDO regulator for VCORE, integrated POR function and on chip clock multiplier PLL (12MHz – 480MHz).
• Asynchronous serial UART interface option with full hardware handshaking and modem interface signals.
• Fully assisted hardware or X-On / X-Off software handshaking.
• UART Interface supports 7/8 bit data, 1/2 stop bits, and Odd/Even/Mark/Space/No Parity.
• Auto-transmit enable control for RS485 serial applications using TXDEN pin.
• Operational configuration mode and USB Description strings configurable in external EEPROM over the USB interface.
• Configurable I/O drive strength (4,8,12 or 16mA) and slew rate.
• Low operating and USB suspend current.
• Supports bus powered, self powered and high-power bus powered USB configurations.
• UHCI/OHCI/EHCI host controller compatible.
• USB Bulk data transfer mode (512 byte packets in Hi-Speed mode).
• +1.8V (chip core) and +3.3V I/O interfacing (+5V Tolerant).
• Extended -40°C to 85°C industrial operating temperature range.
• Compact 64-LD Lead Free LQFP/LQFN package and 56-LD VQFN packages.
• +3.3V single supply operating voltage range.

The post FT2232HQ first appeared on FTDI.

The post FT2232HQ appeared first on FTDI.

FT4232HA features 4 UARTs. Two of these have the option to independently configure an MPSSE engine, this allows the FT4232HA to operate as two UART/Bitbang Ports plus two MPSSE engines used to emulate JTAG, SPI, I2C, Bit-bang or other synchronous serial mode.

The FT4232HA is available in Pb-free (RoHS compliant) 64-pin QFN packages.

The post FT4232HAQ first appeared on FTDI.

The post FT4232HAQ appeared first on FTDI.

Note that the 64 pin variant of this product is now obsolete and is not recommended for new designs. Other packages are not affected.

If there is any demand, please send in your enquiry for special support consideration.

For more information, please click here to contact us.

Vinculum-II (VNC2) is FTDI 2nd generation of USB Host / Slave controllers. The unit features a powerful 16-bit MCU core, with embedded 256KB Flash and 16KB RAM memory. The unit supports a range of flexible interfaces including UART, SPI, FIFO and PWM. The complete USB protocol data processing is handled entirely by hardware resources within the unit freeing up processing resources for user developed applications.

The VNC2 is a fully programmable device and is supported with the new Vinculum Software Tool Suite, which provides an easy to use ‘C’ based development environment to enable user firmware development. The VNC2 offers a complete USB system solution in a single IC.

Or alternatively, the designer can configure VNC2 with one of the many precompiled ROM files developed by FTDI to cover a range of popular interfaces. These are described at Precompiled Firmware.

Key Hardware Features

• Dual USB 2.0 Host / Slave controller.
• Embedded 16-bit Harvard architecture MCU core, with 256KBytes of Flash memory and 16Kbytes RAM.
• 2 x Full-Speed / Low-speed USB 2.0 ports supporting Host or Slave operation.
• Programmable UART interface, supports up to 6MBaud transfers.
• 8-bit wide FIFO interface.
• 2 x SPI slave interfaces, 1 x SPI master interface.
• PWM (Pulse Width Modulation) interface.
• 4 channel DMA controller, and general purpose timers.
• Support for reduced power modes.
• Two packages size options (32-/48-pin QFN and LQFP packages).
• Backwards compatible with VNC1L with 48-pin LQFP package.
• RoHS compliant, and extended temperature support (-40°C to +85°C).
• Enhanced features with Vinculum Software Tool Suite
• Based on royalty-free flexible ‘C’ based Integrated Development Environment.
• Includes compiler, drivers and RTOS kernel to support user firmware development.
• Debug interface for real-time hardware based code debug.
• Pre-compiled libraries for several USB classes including FAT file system support.

NOTE: VNC2 devices are supplied unprogrammed

The post VNC2-48Q1C first appeared on FTDI.

The post VNC2-48Q1C appeared first on FTDI.

The Vinculum family of USB Host Controller ICs not only handle the USB Host Interface and data transfer functions, but owing to the inbuilt 8/32-bit MCU and embedded Flash memory, Vinculum encapsulates the USB unit classes as well. When interfacing to mass storage units such as USB Flash drives, Vinculum also transparently handles the FAT file structure communicating via UART, SPI or parallel FIFO interfaces via a simple to implement command set.

The VNC1L is the first generation device of the FTDI Vinculum family of USB Host / Slave Controller ICs, which are designed to deliver USB Host level interfacing capabilities to embedded applications. The VNC1L features two independent USB Host / Slave ports with an inbuilt 8/32-bit MCU processing core with 4KBytes of RAM program memory and 64KBytes of embedded Flash memory for firmware storage. The VNC1L supports UART, SPI slave and 8-bit parallel FIFO interfaces to enable communication with external processing devices. Further the two USB Ports on the VNC1L can be individually configured by firmware as Host or Slave ports.

VNC1L can be programmed with FTDI’s in-house developed firmwares which supports a range of common USB device classes, providing a cost effective, complete, ready-to-use USB interfacing solution. Users do not need to license any USB software stacks or develop USB drivers, indeed no knowledge of USB is required to use these devices. VNC1L is ideal for implementing USB interfacing within existing applications which do not already have USB, example applications include adding USB Flash drive connectivity to a wide range of consumer and industrial products.

Key Hardware Features

• 8/32 bit V-MCU Core
• Dual DMA controllers for hardware acceleration
• 64k Embedded Flash Program Memory
• 4k internal Data SRAM
• 2 x USB 2.0 Slow/Full speed Host/Slave Ports
• UART, SPI and Parallel FIFO interfaces
• PS2 legacy Keyboard and Mouse Interfaces
• Up to 28 GPIO pins depending on configuration
• 3.3V operation with 5V safe inputs
• Low power operation (25mA running/2mA standby)
• Supplied with FTDI field upgradeable firmware supporting a range of common USB class devices.
• LQFP-48 RoHS compliant package
• Multi-processor configuration capable

NOTE: VNC1L devices are supplied unprogrammed

The post VNC1L-1A (NRND) first appeared on FTDI.

The post VNC1L-1A (NRND) appeared first on FTDI.

Note that the 64 pin variant of this product is now obsolete and is not recommended for new designs. Other packages are not affected.

If there is any demand, please send in your enquiry for special support consideration.

For more information, please click here to contact us.

Vinculum-II (VNC2) is FTDI 2nd generation of USB Host / Slave controllers. The unit features a powerful 16-bit MCU core, with embedded 256KB Flash and 16KB RAM memory. The unit supports a range of flexible interfaces including UART, SPI, FIFO and PWM. The complete USB protocol data processing is handled entirely by hardware resources within the unit freeing up processing resources for user developed applications.

The VNC2 is a fully programmable device and is supported with the new Vinculum Software Tool Suite, which provides an easy to use ‘C’ based development environment to enable user firmware development. The VNC2 offers a complete USB system solution in a single IC. Or alternatively, the designer can configure VNC2 with one of the many precompiled ROM files developed by FTDI to cover a range of popular interfaces. These are described at Precompiled Firmware.

Key Hardware Features

• Dual USB 2.0 Host / Slave controller.
• Embedded 16-bit Harvard architecture MCU core, with 256KBytes of Flash memory and 16Kbytes RAM.
• 2 x Full-Speed / Low-speed USB 2.0 ports supporting Host or Slave operation.
• Programmable UART interface, supports up to 6MBaud transfers.
• 8-bit wide FIFO interface.
• 2 x SPI slave interfaces, 1 x SPI master interface.
• PWM (Pulse Width Modulation) interface.
• 4 channel DMA controller, and general purpose timers.
• Support for reduced power modes.
• Two packages size options (32-/48-pin QFN and LQFP packages).
• Backwards compatible with VNC1L with 48-pin LQFP package.
• RoHS compliant, and extended temperature support (-40°C to +85°C).
• Enhanced features with Vinculum Software Tool Suite
• Based on royalty-free flexible ‘C’ based Integrated Development Environment.
• Includes compiler, drivers and RTOS kernel to support user firmware development.
• Debug interface for real-time hardware based code debug.
• Pre-compiled libraries for several USB classes including FAT file system support.

NOTE: VNC2 devices are supplied unprogrammed

The post VNC2-48L1C first appeared on FTDI.

The post VNC2-48L1C appeared first on FTDI.

Note that the 64 pin variant of this product is now obsolete and is not recommended for new designs. Other packages are not affected.

If there is any demand, please send in your enquiry for special support consideration.

For more information, please click here to contact us.

Vinculum-II (VNC2) is FTDI’s 2nd generation of USB Host / Slave controllers. The device features a powerful 16-bit MCU core, with embedded 256KB Flash and 16KB RAM memory. The device supports a range of flexible interfaces including UART, SPI, FIFO and PWM. The complete USB protocol data processing is handled entirely by hardware resources within the device freeing up processing resources for user developed applications.

The VNC2 is a fully programmable device and is supported with the new Vinculum Software Tool Suite, which provides an easy to use ‘C’ based development environment to enable user firmware development. Or alternatively, the designer can configure VNC2 with one of the many precompiled ROM files developed by FTDI to cover a range of popular interfaces. These are described at Precompiled Firmware. The VNC2 offers a complete USB system solution in a single IC.

Key Hardware Features

• Dual USB 2.0 Host / Slave controller.
• Embedded 16-bit Harvard architecture MCU core, with 256KBytes of Flash memory and 16Kbytes RAM.
• 2 x Full-Speed / Low-speed USB 2.0 ports supporting Host or Slave operation.
• Programmable UART interface, supports up to 6MBaud transfers.
• 8-bit wide FIFO interface.
• 2 x SPI slave interfaces, 1 x SPI master interface.
• PWM (Pulse Width Modulation) interface.
• 4 channel DMA controller, and general purpose timers.
• Support for reduced power modes.
• Two packages size options (32-/48-pin QFN and LQFP packages).
• Backwards compatible with VNC1L with 48-pin LQFP package.
• RoHS compliant, and extended temperature support (-40°C to +85°C).
• Enhanced features with Vinculum Software Tool Suite
• Based on royalty-free flexible ‘C’ based Integrated Development Environment.
• Includes compiler, drivers and RTOS kernel to support user firmware development.
• Debug interface for real-time hardware based code debug.
• Pre-compiled libraries for several USB classes including FAT file system support.

NOTE: VNC2 devices are supplied unprogrammed

The post VNC2-32Q1C first appeared on FTDI.

The post VNC2-32Q1C appeared first on FTDI.

Note that the 64 pin variant of this product is now obsolete and is not recommended for new designs. Other packages are not affected.

If there is any demand, please send in your enquiry for special support consideration.

For more information, please click here to contact us.

Vinculum-II (VNC2) is FTDI’s 2nd generation of USB Host / Slave controllers. The device features a powerful 16-bit MCU core, with embedded 256KB Flash and 16KB RAM memory. The device supports a range of flexible interfaces including UART, SPI, FIFO and PWM. The complete USB protocol data processing is handled entirely by hardware resources within the device freeing up processing resources for user developed applications.

The VNC2 is a fully programmable device and is supported with the new Vinculum Software Tool Suite, which provides an easy to use ‘C’ based development environment to enable user firmware development. Or alternatively, the designer can configure VNC2 with one of the many precompiled ROM files developed by FTDI to cover a range of popular interfaces. These are described at Precompiled Firmware. The VNC2 offers a complete USB system solution in a single IC.

Key Hardware Features

• Dual USB 2.0 Host / Slave controller.
• Embedded 16-bit Harvard architecture MCU core, with 256KBytes of Flash memory and 16Kbytes RAM.
• 2 x Full-Speed / Low-speed USB 2.0 ports supporting Host or Slave operation.
• Programmable UART interface, supports up to 6MBaud transfers.
• 8-bit wide FIFO interface.
• 2 x SPI slave interfaces, 1 x SPI master interface.
• PWM (Pulse Width Modulation) interface.
• 4 channel DMA controller, and general purpose timers.
• Support for reduced power modes.
• Two packages size options (32-/48-pin QFN and LQFP packages).
• Backwards compatible with VNC1L with 48-pin LQFP package.
• RoHS compliant, and extended temperature support (-40°C to +85°C).
• Enhanced features with Vinculum Software Tool Suite
• Based on royalty-free flexible ‘C’ based Integrated Development Environment.
• Includes compiler, drivers and RTOS kernel to support user firmware development.
• Debug interface for real-time hardware based code debug.
• Pre-compiled libraries for several USB classes including FAT file system support.

NOTE: VNC2 devices are supplied unprogrammed

The post VNC2-32L1C first appeared on FTDI.

The post VNC2-32L1C appeared first on FTDI.

The FT312D is a USB 2.0 Full Speed host IC specifically targeted at providing access to peripheral hardware from an Android platform with a USB device port. The device will bridge the USB port to a UART interface via the Android Open Accessory protocol.

The FT312D provides a bridge between peripheral hardware/systems and an Android platform with a USB device port.

The FTDI Chip Android Open Accessory HyperTerm Utility is available for download on Google Play.

Try it out:

Android app on Google Play

Key Hardware Features

• USB 2.0 Full Speed Host
• USB to UART bridge
• USB ERROR indicator pin
• Single power supply operation at 3.3V
• Internal 1.8V LDO regulator
• Internal memory for storing configurable strings – allows Android to automatically detect the device and application
• Extended operating temperature range : -40°C to 85°C
• Available in Pb-free QFN-32 and LQFP-32 packages (RoHS compliant).

The post FT312D-32Q1C first appeared on FTDI.

The post FT312D-32Q1C appeared first on FTDI.

The FT312D provides a bridge between peripheral hardware/systems and an Android platform with a USB device port.

The FT312D will enumerate USB and Android Open Accessory and provide a UART interface for peripheral integration.

Note, proper compatibility requires Android Open Accessory Mode, available in Android platforms 3.1 onwards.

The FTDI Chip Android Open Accessory HyperTerm Utility is available for download on Google Play.

FT312D-32L is available in 32 Pin LQFP packaging.

Try it out:

Android app on Google Play

Key Hardware Features

• USB 2.0 Full Speed Host
• USB to UART bridge
• USB ERROR indicator pin
• Single power supply operation at 3.3V
• Internal 1.8V LDO regulator
• Internal memory for storing configurable strings – allows Android to automatically detect the device and application
• Extended operating temperature range : -40°C to 85°C
• Available in Pb-free QFN-32 and LQFP-32 packages (RoHS compliant).

The post FT312D-32L1C first appeared on FTDI.

The post FT312D-32L1C appeared first on FTDI.

The FT311D provides a bridge between peripheral hardware and an Android platform with a USB device port.

The FT311D will enumerate the Android platform and provide an interface to either, GPIO, UART, PWM, I2C Master, SPI Slave or SPI Master. Note, proper compatibility requires Android Open Accessory Mode, available in Android platforms 3.1 onwards.

The FTDI Chip Android Open Accessory HyperTerm Utility is available for download on Google Play.

Try it out:

Android app on Google Play

FT311D-32Q is available in 32 Pin QFN packaging

Key Hardware Features

• USB 2.0 Full Speed Host
• Hardware selectable interfaces – GPIO, UART, PWM, I2C Master, SPI Slave or SPI Master.
• USB ERROR indicator pin.
• Single power supply operation at 3.3V.
• Internal 1.8V LDO regulator.
• Internal memory for storing configurable strings – allows Android to automatically detect the device and application.
• Extended operating temperature range : -40°C to 85°C.
• Available in Pb-free QFN-32 and LQFP-32 packages (RoHS compliant).

The post FT311D-32Q1C first appeared on FTDI.

The post FT311D-32Q1C appeared first on FTDI.